Tile is one of the most common finishing materials. But it is necessary to mount it on a well-fortified basis, for example, on a concrete tie. Now many masters are wondering if it is possible to lay a tile on the wooden floor? It is possible, however, you need to know all the features of this process.

In order for all your work to do not go the pump, it is necessary to have a durable and solid foundation. Its preparation includes such actions:

  1. Definition type floor. Make it is not difficult. Mostly in the houses use laminate, parquet or boards.
  2. Dismantling or repairing an old coating. This procedure should be carried out almost always, otherwise the new finish may be poor quality. Pay special attention to lags. You may need to additionally process them with an antiseptic or replace.
  3. Check the level of the base in the house. If it is uneven, then it is possible to correct this deficiency with wooden trimming.
  4. . For this, there is a clamzite between the lags, not forgetting about the air cushion.
  5. Elimination of holes and cracks using a special putty designed for wood. The dried smear should be sanded. If the slots are very large, then hammer them with wood chips mixed with glue. The protruding parts should be scraped.
  6. Removing the old lacquer coating or paint. To do this, you can apply such methods: thermal, chemical or mechanical. The first assumes the use of a construction dryer. After heating the paint or varnish, the layer is removed with a spatula. The second method provides for coating cleaning with chemicals. The third method is the most time consuming, since it assumes manual removal of paint with a metal brush or sandpaper.

Before being produced on the wooden floor, you need to process it with latex impregnation or hot oil. Between the draft floor and walls do not forget to leave the technological gap of 5 mm to compensate for expansion and narrowing the material. Subsequently, close it with the mounting foam.

Note that the hot olife is flammable, so it should work with it as accurately as possible.

How to make the basis more solid and durable?

For laying tiles in the house, it is necessary to achieve the black floor to be perfect. To do this, have to make a screed. But it must be smooth, since the wooden base may not withstand large loads. There are several screed options:

  • Cement. Please note that its layer should not exceed 3 cm. Now there are already ready-made compositions in stores that need to simply dilute according to the instructions.
  • Glue. In this case, you can apply a polyurethane composition or a means based on liquid glass. But it is poured on a molar or metal reinforcing grid. It allows you to significantly strengthen the foundation. Usually the grid is fixed with self-draws. Pouring can be made personally. To do this, mix 2 pieces of sand with 2 parts of liquid glass and 1 part of water. Sand is needed to improve gluing cladding to the floor surface.
  • Using, plywood or drywall. These materials will allow you to quickly align the level of the base. Most often used Paneur. She more firmly and can serve not one year. It is necessary to put it right. Screw it should be screwed.

While working, use the construction level. Note that if you are preparing the base in the kitchen or in the bathroom, it is better to purchase moisture-resistant Phaneur.

If you have prepared a reason correctly, you can start laying ceramic tiles. You can do it with your own hands.

Montaja technology

What tools and materials are needed?

Laying tiles on the wooden floor is made after the preparation of all devices and materials. You will need:

  • Porcelain stoneware or other tile. Note that you need to purchase 10-15% more than you need. The fact is that some elements can be defective or crash during the installation process. In addition, the material will probably have to cut;
  • Glue. There must be high-quality and elastic, it should be chosen correctly;
  • Drill with a special nozzle for glue stirring and pure capacity for it;
  • Bulgarian (in order to cut the fane), plates;
  • Building level;
  • Spatula gear;
  • Rubber hammer or kiyanka;
  • Construction crosses to ensure the same interputric seams;
  • Machining of the appropriate shade or white color;
  • Threads for room markup.

Now you can proceed to the installation of ceramic facing. All procedures are made by their own hands, although the assistant does not hurt you.

Laying tiles

So, if you have already secured and treated Phaneur, and also collected tools, you can start work. It implies the implementation of such actions:

  • To begin with, decide which method you apply to stick ceramics. In order for its location to be optimal, stretch from the middle of the wall at right angles. From the other wall, make the same markup. Both lines must intersect perpendicularly. They serve to mark the room. Note that before installing the tile, you need to remove the plinth and door jambs.
  • Next, on the Fanora, spread the tile. Consider extended lines. If you want to save the tile, you can easily shift them.
  • Now apply glue on the basis. Match small portions of plywood - no more than 1 m2. Otherwise, he quickly becomes not elastic and useless. For uniform glue application, use a toothed spatula.
  • After that, you can fix the fastening of porcelain stoneware to the base. Apply your own hands the element with a rough surface to the glue and put on it to it. Installation must be carried out on one of the outlined lines until the entire smeared section of the floor is covered with ceramic tiles.
  • Fighting on the glue is needed towards the walls to the walls. At the same time, do not forget to follow the markup.
  • If you have already reached the walls, you can fill the remaining ceramics gaps. For this tile will have to cut. In principle, you can do it with your own hands using stoveturis. However, for the safety net, find yourself an assistant.

Finish finish and some installation features

After the glue dries, you can start the seams of seams between the ceramic tiles. For this, the rubber spatula is suitable. While the master did not dry, its surplus is desirable to remove with a damp pure sponge. The dry tissue cloth is subsequent polished finish.


The photo shows the process of tile grout rubber spatula. Surplus the material immediately remove with a dry sponge or cloth.

After completely drying the floor, the surface of the ceramic tile can be treated with a special primer. However, most types of facing presented already have such a coating.

While working constantly monitor the level of the material. If some elements are a bit thinner than others, then under them to put the adhesive base. Kiyanka is used to align the elements. But knocking directly on the ceramic finish is not worth it. A bar is substituted under the Cyans.


Plastic crosses presented in the photo are used to align the seam between the tiles.

Note that the adhesive should not smear the tile itself. It is necessary to apply it only on Faneur or another base. We must not forget that the installation can be both suture and seamless. The second version of the laying can also be made with your own hands. If you still decided to choose the first type of installation, then use special crosses. They can have a different size and provide a different width of the seam.

As you can see, do it yourself to make all the work it is not difficult if you figure it out in its specifics. It is possible to put the tile on the wooden floor, you only need to competently prepare the base.