How to make an antenna for a TV with your own hands so that it does not give way to the quality of the purchase device, such a question interests many home masters and television chiefs. There are various ways to make an antenna yourself, from the most simple designs, to the instruments of the receiving satellite signal.

This option is suitable for people who want to install at home or in the country's ordinary room antenna to view federal channels. Describing such a device for everyone, special knowledge is not required.

This is the most elementary way, so it will only be necessary copper wire 70-90 cm, 2-3 mm thick. The room antenna is manufactured as follows:

  1. Clean both ends of copper wire.
  2. One end to secure the battery, and the other insert into the TV connector.

The signal will appear immediately, the user will become available from 1 to 5 channels. So simple method, you can make it possible to make a home antenna in 5 minutes.

The most popular way of making antenna with your own hands from girlfriend. For the manufacture you will need beer banks. Experts argue that in order to assemble an antenna from beer cans will need no more than an hour.

You will need:

  1. Connecting cable.
  2. Several beans from beer.
  3. Plug.
  4. Screws in the amount of 2 pieces.
  5. Screwdrivers.
  6. Insulating tape or heat shrink tube.
  7. Wooden timber or metal pipe for antenna mounting.

You can make a homemade antenna from tin cans according to the following scheme:


This is another easy option, how to make a television antenna in a short time. The device is well catches a signal, providing high image quality.

Ovrevian antenna with amplifier

Version antenna with an amplifier can be different configurations. It is spent on its assembly than the first two options. But the advantage is that it is very powerful, and takes all the analog channels in excellent quality. One of the common options for an overvustrial antenna forms "Butterfly".

Instruments:

  1. Board or plywood sheet, dimensions 550/70/5 mm.
  2. Copper wire.
  3. Connecting PC75 cable.
  4. Drill.
  5. Soldering iron.
  6. Plug.

Instruction:

Television antenna with their own hands is ready to work.

Decimeter antenna

Homemade antennas that capture the decimeter signal can be of various configurations.

Option 1

The easiest option is considered it is relatively easy and just to collect.

You will need:

  1. Plywood.
  2. Cord.
  3. Soldering iron.

Instruction:

  1. Make from connecting cable ring, size 53 cm.
  2. Cut another piece of cable for the manufacture of the loop, size is 17.5 cm.
  3. To the ring you need to solder a loop, and the cable that will be inserted into the screen.
  4. Attach the design on the fane.
  5. Direct the assembled device towards the TV television.

Thus, the antenna of the DMW range is collected with his own hands.

Option 2.

Another possible method of manufacturing Teleantenna DMB rangecalled "eight".

Instruments:

  1. Wire (copper, aluminum).
  2. Adhesive pistol.
  3. Cable.
  4. Lubes.

Instruction:


This is another way to make an antenna yourself.

This device has a signal range reach up to 490 MHzThis means that the picture quality will be very high. But for the manufacture you need to purchase a transformer.

You will need:

  1. Transformer.
  2. Foil.
  3. Glue.
  4. Roulette.
  5. Cardboard.
  6. Stapler.
  7. Marker.

Instruction:


The device is ready to work.

Satellite plate with your own hands

One of the most popular questions is it possible to make a satellite antenna with your own hands? On the Internet there are many videos, how to make a plate to view satellite television yourself.

Did this device at home can be in two ways:

  1. Deep on the matrix.
  2. Spike mesh and wire.

The most optimal and convenient is the first way of manufacture. To do this, make a drawing of the future device. To this stage, the work should be approached very responsibly, calculate all the parameters exactly, otherwise the device will be released at the output. Parabola is carried out in the drawing, which is then transferred to the steel sheet. Its thickness should be 0.05 cm.

Stages of work

  1. With the help of the welding machine, make a steel frame with a diameter of 9-10 cm. Steel rods are turned on the outer side, and the bearing is welded into the center.
  2. The resulting design is installed on the level place, and the pipe is attached to the installed bearing, then the knife is installed.
  3. Then the frame is poured with concrete mortar and will dry 5 days.

In the final stage, it is necessary to remove the antenna, this can be done in different ways. Recommended work recommended divide the design on 8 parts.Fiberglass or epoxy soil is applied for the duct.

On the dried concrete form, put the engine oil, insert the pipe into the washer. After a homemade plate is covered with a resin and a fiberglass shower occurs. The process of manufacturing the device is completed. Read also.