As practice shows, quite often many people for one reason or another are not satisfied with the common body antennas and they are forced to make self-made. The most interesting thing is that create an antenna with your own hands, and from the remedies - quite simple. Next, we will present to your attention the most famous methods for which the self-made antenna makes.

Algorithm of beer cans

This is the most famous television antenna that makes it yourself. The specificity is the elementality and simplicity of the components. This device can be made in a country house and even on a picnic, as well as in the apartment, where from the usual antenna, sometimes, not 100% reception. Experts claim: what to make a similar antenna with their own hands - takes only 15 minutes of time, and "catches" the device is much more TV channels than the standard one.

So, if we want to create a receiver from ordinary cans, we will need:

The work process is all with your own hands:

  • We adhere to the tape stick to the banks, we observe the interval of approximately 8 centimeters (between them), although you should choose the length of the eye. If the bank has a rings, the cable is allowed to fix the screws
  • Screw the screws in the beer container, we clean the two ends of the antenna cable and screw to the screws to the screws
  • Bind the cable using the cable using the scotch, it is necessary for the resistance of the received receiver.
  • You can use the usual hanger instead of the same stick. By the way, then tune will be much easier
  • If we want the antenna to not lose its functionality (after heavy rain, thunderstorms, etc.), then the banks cover the large "plastic bottle" (preferably 2 liter), which cut off the bottom and neck. In the middle of the bottle, drills a hole through which stretch the cord, after connecting this area to quivel. It is necessary to note that plastic at such a temperature will change its own design plus make the rendered hole tightly (i.e. hermetically) closed

The antenna made from the template beam cans is completely ready, it remains only to connect it to "TV" and adjust. You can improve the device by using several sections from a similar container.


Normal television antenna

If you are new to this case, and try to make the antenna with your own hands still hunt, you need to try to make the following design:


  • We connect an antenna entrance to a TV with any metal contour, in advance of the wounded tape
  • Contour put on the stand from plastic material or wooden or on the balcony
  • We connect the TV with an antenna using the plug plus the cable, in the latter cut off the insulation of approximately 6 centimeters in length
  • Opened winding we divide into 2 parts and flex
  • Immediately, the winding is already tightly cutting with the same length and barbel the cable itself
  • In the plug, fasten with screws with winding. When there is no place in the presented plug in order to fasten the winding, then it is necessary to cut it
  • The second edge of the cable is fixed on the contour, first clean up according to the previous scheme, we make a ring from the vein and fix
  • Connection zones need to be wrapped with a tape to make a device more reliable

In order to increase the signal on the current receiver, the signal amplifiers should be applied.

Powerful television antenna

If we want the device to function as an ordinary antenna, improve its receiving circuit. For this you need:

  • Purchase equipment - a reinforcing signal that is connected specifically to the device definitely - to wind the cable at two ends of the insulating ribbon to eliminate interference in the signal
  • For high-quality reception, it is necessary to make the screen - a kind of metal mesh, which is isolated from the TV and installed behind the receiver. As the screen itself can apply a metal mesh from a conventional fence
  • The reception area should be strengthened, because - moreover, the screens can be added iron bars. Moreover, that the design is from one metal and excludes the oxidation factor. We connect the rods with the screen symmetrically, in order to make the square as much as possible.
  • In the center of the installation you need to place another amplifier, while we soldes the contacts to our receiver
  • Antenna data for the TV in the house are not mounted, often they are put on the roof, by mounting themselves to the nearest television tower

Construct antenna from "Nothing"

There are 2 absolutely simple ways, how to build an antenna for TV at home (and with your own hands):

  • You can use the most common wire, just not to take aluminum (it is quickly oxidized). For this, a typical wire from copper or brass will be perfectly suitable. We purify it from both ends of the insulating material, 1 edge is attached to the battery or a pipe, and the other insert into the TV connector. The signal occurs instantly, since the pipe, after the passage through a significant part of the building, plus leaving "upstairs" appears to be a good frequency amplifier. You can make a good home antenna and "catch" approximately 5 channels like this method.


  • Well, the 2nd option is suitable for people who have a balcony. In this case, it is necessary to take the same wire, already more authentic, in order to connect the device and the balcony site. We clean this wire from 2 sides and 1 end connect to TV (where the cable socket), and the 2nd primaries the stretched strings to which lingerie hangs

This method is not easy only to help multiply existing channels (building a home antenna for a TV), but also improves the image quality several times.

https://www.youtube.com/results?Search_Query\u003d%D0%B0%D0%BD%D1%82%D0%B5%D0%BD%D0+%BD%D0%B0+%D1%81%D0%B2 % D0% B% D0% B8% D0% BC% D0% B8 +% D1% 80% D1% 83% D0% BA% D0% B0% D0% BC% D0% B8