Tinted film, glued to the glass of the car, no longer surprise. This is a common element of tuning, helping to significantly transform the “iron horse”, giving it a more serious look. But sometimes circumstances force the driver to remove the tint. In this case, knowledge will be useful.
This article describes several useful ways that will be useful not only for experienced motorists, but also for beginners. The proposed methods will help to cope with the removal of the tint film.
Why the driver is forced to remove the tint
In most cases, the reason is a penalty for breaking the toning rules. It is forbidden to glue any film on the windshield, except for the upper strip. The front side windows are allowed to glue over toning, which transmits at least 70% of the light. Rear windows have no restrictions, however, if they are stuck on a mirror film, then it should be removed.
Another common cause is film aging. For a long time of operation, toning fades or various defects appear on it. Air bubbles and film peeling give the car a not presentable look.
How to remove the tint yourself
Tinting can quickly and accurately remove in the service station. But if it is not possible to use the services of a specialist, then you will be able to remove the film yourself. The process of rastonirovanija glasses at the beginner can take a long time. To speed up the job, ask someone to help you.
An important stage in removing tinting is preparation. It is necessary to remove all linings and seals that may be damaged by tools. To remove the old tint film there are four simple ways:
Simple tearing of the film
You will need:
- sharp knife;
- a little patience.
The main advantage of this method is the minimum set of necessary tools at hand. In the upper corner of the glass pry edge toning. Then start pulling the film towards you and down a little. Tinting should be separated from the glass diagonally. Keep it taut all the way along the length of the break and slowly pull it off. It will take a lot of time. But the tearing process can be accelerated. To do this, divide the tint into strips 15 cm wide. Use a knife carefully to avoid damaging the glass.
Using a cleaning solution
You will need:
- water;
- any detergent;
- spray gun;
- sharp knife.
Prepare the solution, it should include: one liter of water and about thirty milliliters of detergent. Pour the solution into a small spray bottle and mix well. Spray the mixture onto the upper edge of the glass and wait about one minute. During this time, the solution will penetrate between the film and glass, weakening the adhesive base. After waiting, peel off the film with a sharp knife on the edge of the glass and carefully pull it down.
Separating a small area, again sprinkle with a solution to the place of separation and wait half a minute. Then continue to separate a small portion of the film - and so on to the bottom of the glass. It is important to remember that everything needs to be done without jerking, distributing efforts evenly.
By heating
You will need:
- building or household hair dryer;
- partner.
The best tool for removing old tint film is any building dryer. You can use household, but the whole process takes much more time.
When using a building hair dryer, set the button at the minimum temperature, and set the maximum on the home appliance. Again, start at the top of the window. Heat the glass as much as possible and pull off the edge of the film. Separating a small piece, again warm up the bottom part of the toning. Thus, it will be easy to remove the entire film from the glass.
The most convenient way to do this two people. One heats the film, and the second slowly and constantly pulls it down, taking it away from the glass. We must remember that you should not do this in the winter outdoors. In this case, the glass will crack from a sharp temperature drop.
With the help of a special solvent
You will need:
- a can of solvent;
- scraper;
- dry rags.
The stores sell a special liquid in a canister that dissolves the tint. It is applied on film and left for fifteen minutes. After the expiration of the specified time, the dissolved toning will easily separate from the glass surface. It is also used to remove residual glue. Fluid easily penetrates under the door trim, causing metal to corrode or wiring to close. To prevent this, place a rag on top of the door trim.
Features remove tinting from the rear window
Difficulties when removing tinting from the rear window appear due to electrical filaments. They can easily be damaged by tearing off the film in the usual way. To prevent this, you need to be careful in work. The difficulty also causes inconvenient rear window layout.To separate the film you need to start from the side and along the threads. The pullout force should be smooth and smooth. To accelerate the separation of tinting from the glass, use a cleaning solution. After removing the tinting remains to remove residual glue from the surface of the glass.
How to remove glue residue
In most cases, to remove residual adhesive base, it is sufficient to use any cleaning agent and a soft scraper. If the glue on the surface of the glass was long enough, then it is better to remove it with acetone, gasoline or high-grade alcohol. At the same time, it is necessary to protect the trim of the doors and car seats from the ingress of these substances. Do not forget to use protective equipment for hands and respiratory tract.
This article has reviewed a few simple ways. All of them are proven in practice by many motorists. Choose for yourself what suits you best. Be careful while working and then you will succeed.
Video: how to remove tinted vacuum
For me, the situation is really incomprehensible when young “boys” drive on fully tinted cars, because you can only dim the rear side and main windows. Sooner or later the police will catch them and issue a fine. Of course, now there are different types, but I do not think that the thugs do not set themselves such, because their value will be higher than their entire car as a whole. In general, sooner or later, “having eaten” the fines will have to tear off the front tint, you can do it yourself, but you need to do it right, because the glue on the glass, which is not so easy to remove, can actually remain. Today I will give some tips on how to remove it with my own hands ...
Personally, I think they have become toned (newly) because now only a fine of 500 rubles is in effect, the numbers have ceased to be rented. Here and again rushed, because our young people no fines or fines!
However, who still thinks about the removal, I just want to warn you - with improper removal, strips of glue remain on the glass, which is not so easy to wipe off. Personally, I was at the station, it was practically cut off, but everything is in order.
Correct withdrawal
In general, experts in tinting, they say that the film can be removed without any divorce and rubbing. The main thing to do is right.
The method is actually simple - just heat the glass to 40 - 60 degrees Celsius and the film will come off along with the adhesive base itself. It is enough just to pick it up with a knife and pull it down. This can be done with an industrial hair dryer, which heats the surface of the window. Thus, the composition remains on the film, not on the glass. If we remove on the sides, then it is advisable to lower the glass sheet halfway and then heat it with a hairdryer and pull it down quietly.
This is the most correct method, after which 90% of adhesive composition does not remain. But there are a couple of minuses:
1) Not everyone has such an industrial hairdryer.
2) They really can damage the plastic upholstery of doors, you need to be very careful, it is desirable to protect the upholstery with wet rags.
3) As a rule, it breaks down from the “sides” at the traffic police inspector, and what a hair dryer! Everything breaks down in a "rush" in order not to pay a fine, but often in scraps.
The basic methods of removing their own hands
1) Guys if you still got into the situation with the traffic police officer, then try to tear off the film in one motion - you need to pry the edge with a knife, then take the canvas with both hands and sharply pull down how strong you are. You won't be able to get rid of the adhesive composition completely, but it will remain much less.
2) If you have time, then you need to pry the edge of the canvas with a knife and with the help of soapy water, slowly remove it from the glass. Soapy water is added to the place of separation, we pour it abundantly, so part of the glue will remain on the film.
By the way, here is a useful video where the guy wiped off with a regular sponge for washing dishes.
But nevertheless, it will not be possible to completely remove it, a part of the glue will remain on the glass; And you need to remove, because you can easily break the glass, they will not work because on the canvas in the glue, which will not allow the glass to fall. YES and everything will stick, starting from dust, ending with all kinds of midges.
What is adhesive film
I want to say a few words about the composition itself, why is it so firmly seated and not moving away?
The adhesive composition is a high level adhesive coating.
Adhesives - These are substances that combine various materials with the help of surface adhesion. They can be brushed off - adhesives, resins, bitumens, some types of transparent varnishes, liquid polymers, etc. The stronger this composition, the stronger (more durable) the film sits on the glass, the harder it is to tear off or remove. For example, some Chinese films fall off on their own, which means that it is an adhesive, of poor quality.
By the principle of application, these compositions also differ, each working under its own conditions:
1) PS (Pressure Sensitive) composition (usually adhesives) - begin to work under pressure, that is, the film must be pressed on the canvas. Now practically they are not used any more, it is a kind of first generation of adhesives.
2) DPS (Detackified Pressure Sensitive) - the composition is activated after applying water. Probably, many have seen the masters wet the glass before applying the film. One of the most common types.
3) CD - starts to work with increasing temperature, that is, you need to heat to glue.
4) CDF - the film is glued with a special solution from the manufacturer.
5) PS / DT - also activated by water. However, there should be a moderate amount of water (excess, you can remove it with a special scraper), otherwise “bubbles” can go.
As you can see there are a lot of adhesives, and therefore it is necessary to scrub them differently, one practical advice does not exist, everything is individual.
Glue removal, various methods
Here we come to the main point in our article, I will try to describe the main methods of removing the adhesive composition:
1) The method of cutting or scraping. Usually perform a special scraper or a special spatula, if not, you can use a conventional blade from a cheap razor. We take a spray with soapy water, spray it on the glass and then begin to cut off a layer of glue.
The method is long, but really the best, then I advise you to walk with either alcohol or a solvent. We watch a small video clip to understand the process.
2) Solvent use - usually alcohol, acetone, gasoline or kerosene. We moisten a rag or sponge with a solvent, then we thoroughly wipe the surface - wait a couple of minutes, then scrape the glue layer, it will become soft and will be cleaned even with a plastic card, which we don’t need in bulk (I don’t need). The disadvantage of this method is smell and flammability, because gasoline, kerosene, etc. may spark from the slightest spark.
3) Special remedy. Means for removing tinting are sold, it works almost as well as solvents, apply - wait - clean off with a plastic scraper, often included.
4) rust converter. In some forums, people filmed using STAR WAX, which converts rust. Apply, wait 5 - 10 minutes, then just scrub with a rag.
5) Antikley - composition for removing various compositions, suitable even for superglue.
6) WD-40 and Antirain - also go to the forums to serve that these famous compounds can contribute to the departure of the adhesive from the glass.
7) Profoam 2000 - household cleaner for removing stickers, tape and other adhesive tapes. You can buy in the shops of industrial goods.
8) Body cleaning liquid for insects. They really mass, you need to take stronger.
9) By the way, there is a video in the network where the guy just rubs with a sponge for washing dishes soaked in water. The main thing he waited a couple of days until the glue dries.
10) Most probably the ridiculous method is the processing of the KOKA-KOLOY glue, some assure that after applying a couple of times the glass can then be wiped off.
In any case, experiment - you will understand with what composition your glue reacts. From myself I note - clean the side windows in the first method, yet it is the most proven (albeit long). But if you plan to clean the rear window, be careful here, because there are heated threads there, and you can easily damage them with a scraper or blade! So try other options.
That's all, I think the information will help you. Read our autoblog.
To date, black tinted surprise no one, at the same time, it is contrary to the law, according to which for exceeding the standard light transmission ability on the offender fined. To avoid fine or just to make the glass again transparent, you should remove the tint film from the windows of the car.
There are two options: to drive away the car in the service station, or to dismantle the tinting with your own hands. The following tools will be required for self-dismantling:
- clean rags;
- any detergent (for example, “Fairy”) with a sprinkler;
- new construction or razor blade with holder;
- technical hair dryer (in the absence of a building hair dryer, you can use a household).
Using these tools, in just an hour and a half, it is possible to completely peel the tint film away from car windows. The procedure is as follows:
- Pry off the top edge of the film with the blade.
- Spray the detergent into the opened gap.
- Peel off the tint as much as possible, then apply the washing liquid again and completely remove the film from the glass (if the tinting does not go, you should methodically heat the glass with a hair dryer, from a distance of 20-30 centimeters. The film should warm up by 40 or a little more, but should not while melting).
- Remove the remaining glue on the glass with white spirit.
- To remove stains and improve gloss, you can rub the glass with a preservative polish.
During operation, it should be noted that in some machines glass may be softer than usual, therefore, wielding the blade, there is a chance to leave scratches on them (it happens very rarely). To avoid such an incident, it makes sense to experiment on a hidden part of the glass.
Razor blade helps get rid of the most resistant tinting. If the glass is hard enough, as happens in most cases, then scratching them with a blade will not work even if desired. However, the blade should work on the wet, namely with the help of a soap solution.
It is recommended to stock up in advance with new blades and purchase a special holder for them. All razor blades have a slightly rounded edge. This form eliminates the face cut when shaving, and in our case - protects the glass from scratches. The main thing when working with a blade is not to hurry and patiently, centimeter by centimeter, to clean the glass.
On a note
Organic solvents are useless in the matter of removing tinting. They do not react with the film, and for the very tinting is very good. Otherwise, even a drop of gasoline could leave a mark on the film.
How to remove the old tint from the car window?
The longer the film stays on the glass, the harder it is. Three years later, when removed, it is likely to go rags. To remove it, you can use a special tool to remove tinting. After applying this tool, the film softens and can be “washed off” with warm water.
Before removing the film, it is advisable to remove the tinted windows from the car and soak them for a few minutes in warm water (40-45 ° C). Make it more comfortable in the bathroom. It is best to work with each glass separately, soaking them and cleaning them in turn.
It is possible that part of the film in the form of patches will remain on the glass, especially if it is very old. You can get rid of them with a blade, as described above. It is convenient to work with a blade right in the water. The risk of scratching the glass is minimal.
If there are no appropriate conditions and all the necessary tools, then you can always contact the auto repair service for help. However, it should be remembered that professional removal of tinting is expensive. Therefore, if you want to save a decent amount, it is better to work independently.
On a note
Never try to remove the film with a building dryer, by melting it. The film, therefore, is unlikely to easily move away, but the glass may burst.
Now you understand how to remove the tint from the glass of the car with your own hands, so feel free to act and hope for the first, faster way.
Toning that is easy to remove
In addition to the usual tinting of vinyl or polycarbonate, there is also silicone. This is the so-called "removable toning." The advantage of siliconized film is that it is reusable. Possessing considerable elasticity, it practically does not tear and is not crushed.
You can install and remove the siliconized film up to 5 thousand times (manufacturers information). It is glued in almost the same way as regular toning, but it is removed much easier - in one motion. Simply pry the corner with the blade and pull the edge of the canvas.
The cost of the silicone film is almost the same as that of the "disposable". Therefore, if a car is tinted with a film with a transparency of less than 75% (at your own peril and risk), then it is advisable to choose a material based on silicone. When it comes time to raston the car, it can be done in a few minutes. At the same time the film will remain unscathed, and it can be used many more times.
Alternative to tint
In addition to the temporary tinting, which was mentioned in the previous chapter, you can protect the salon from overheating and excessive curiosity of others, using a number of other means. First of all, it should be noted that the permitted toning also largely protects the interior from the sun. And if the problem lies only in this, darkening the glass by 20-25% can no longer worry about the salon trim.
At the same time, you can do without a film at all or combine the permitted tint with additional tools. So, you can buy protective screens on suction cups or retractable curtains. When buying screens on suction cups should pay attention to the material of the latter. Best kept silicone suction cups. They are softer and do not peel off when heated.
As an alternative to the usual dimming of glasses can be considered electronic tint. It is a special film connected to a DC source. When electricity is passed through the liquid-crystal structure built into it, the film instantly becomes dark. After cessation of current supply, the electrochromic film becomes transparent again.
What is dubbing film for? - To get rid of bright sunlight, close from prying eyes everything that happens in the cabin and keep cool inside the car (this is especially true in the summer heat).
That is why many car enthusiasts glue tint to almost all car windows (and even the headlights).
But what if the film is no longer needed? - There are two options - pay for the services of professionals to the service station or remove the tint yourself.
The first method is simple but costly (specialists will have to pay). So we give preference to the second option. Moreover, you will definitely not have any particular difficulties with such work.
When to remove the tint from the car?
It would seem, why remove the tint, if it is so useful. There can be several reasons:
- You bought a new car with a film already pasted, but it does not suit you in terms of light transmission ability;
- you decided to remove the tint due to the constant stops of inspectors on the road and fines (the reason is that the film does not comply with the requirements of traffic regulations). Recall that the light transmission capacity of all glasses must be at least 70%;
- prolonged operation to the appearance of damage on the surface of the film itself. For example, it appeared bloating, air bubbles, sticky parts, and so on. As a rule, such a film does not decorate, but spoils the car;
- film stripping is required for repair windshield cracks , or the elimination of cleavage.
How to remove the tint from the car window?
If you decide to act independently, you must clearly know how to remove the old tint, and what tools for this will be needed.
On the one hand, there is nothing difficult here, but on the other hand, you must prevent pieces of toning from tearing off. Otherwise you will spend a lot of time removing them. In general, about everything in order.
Let's select the most simple, reliable and effective ways to dismantle tinting:
1. Option One - heated. So, to do the work you need an assistant and a hair dryer. Alternatively, you can use more affordable home appliances - a steamer or a hair dryer for drying hair.
Please note that this work must be done in warm weather (preferably from five degrees of heat and above).
Otherwise, cracks may occur due to a sharp temperature drop. Warm the glass to 40-45 degrees Celsius (no longer needed).
This is enough to soften the glue and not accidentally melt the tint film together with the plastic (rubber) elements of the car.
How to do the work? Act this way. One person warms the glass with a hair dryer (steamer), and the second person hooks the edge of the film with a blade and starts pulling it towards himself.
Council The main thing is not to hurry, act carefully so that the film does not tear, so it will be easier to remove.
To do the job well, proceed as slowly as possible. If you pull quickly, then toning will break, and the work will take much longer. Why? - Yes, because you have to remove each piece separately and rub the glue for a long time.
The glass with the film must be heated gradually as it is removed. It is important to avoid the ingress of heat on the elements of plastic or rubber (this can lead to their deformation).
So, step by step you will remove the entire film. A few minutes and the work is ready. Now you have useful information on how to remove the tint from the glass using a regular hair dryer. It remains to apply the knowledge in practice.
2. The second option - without heating. But what to do if you do not have a hairdryer or steamer on hand? - Do not despair. For such a case, there is also a good method.
Here you will need the usual detergent, a blade, a scraper, acetone (solvent) and a soft cloth.
Perform toning removal work in the following sequence:
- Find the edge of tinting and pry it with a blade;
- start slowly pulling the film over yourself (there should not be excessive force) and pour the already cleaned glass with water and detergent. So step by step, remove all the tint.
- Remember that it is important to act as slowly as possible. Any sudden movement can lead to rupture of the film (we already mentioned the consequences above);
- as soon as the film is removed, take a special scraper and remove the remaining glue stains.
- As a rule, the detergent has already done its job and soaked the existing “chemistry”;
- if, upon completion of the cleaning, persistent glue stains remain, then special formulations can be used. If these are not at hand - use acetone or solvent;
- after completion of all work, thoroughly rinse the surface with warm water. Remove the remaining moisture with a dry and soft cloth.
When doing work, try not to let detergent composition and water under the door trim. This may lead to a decrease in elasticity and elasticity of the rubber elements. It is enough to put a piece of cloth on the seal.
To implement this method can be approached in a different way. Dilute the detergent in warm water and apply the composition to the glass. From time to time moisten the surface, preventing it from drying out.
After 30-40 minutes, the tint film will soften and easily peel off. Further steps to remove the glue are similar to what we considered above.
Tinted rear window and headlights
One of the most difficult tasks is to remove the tinted glass from the rear window. Here act very carefully so as not to damage the heated threads.
The best option is with the use of a hair dryer, which will soften the adhesive qualitatively and make it possible to remove the tint without damage.
As in the previous cases, pull the film as slowly as possible and watch the heating threads (do not allow them to break).
Many are interested in how to remove the tint from the headlights. But there are also no secrets here - choose one of the methods described above and act.
If everything is done correctly, then you will remove the extra tint in just 10-15 minutes and save a few thousand rubles. The main thing in this business is to prepare well and act without haste. Good luck to you work.
One of the prerequisites that must be fulfilled before tinting a car is to remove the old film, which has already been applied to the glass, as well as to thoroughly clean and wash the windows. And sometimes you may need to remove the tint from the glass at the request of the inspectors of the road patrol service, if you had it inflicted with violations of traffic regulations.
Sometimes there are situations when crossing the border, when, directly at the checkpoint, border guards offer remove tinted glass. And in case of failure, turn the car back.
Of course, such situations are possible if you have tinted front side windows and windshield. By law, the light transmission of the front side windows should be 70%, and frontal - 75%.
Yes, the mirror film can not be used even on the rear window and rear side. If the patrol suspects that there is something wrong with the tinting, he can offer to remove it on the spot.
Most high-quality tint films of American production, even after several years of operation, are removed very easily. But, if the film is of poor quality, it can be difficult to remove, it can be torn off, leaving glue on the glass.
Sometimes you can observe how people who do not have experience removing tinting, try to tear it off and clean the glue with newspapers, rags, solvents or gasoline. They suffer, spending a lot of time and effort.
How to independently remove the tint from the glass
In fact, the film is removed much easier and faster. For this we need:
- a scraper, or a knife blade,
- soapy water (well suited with a small amount of baby shampoo, like “quack-quack” or dishwashing detergent, such as “Fairy”),
- sponge for washing dishes.
- Remove the door cards, as when applying the film, it is not necessary.
First you need to pry the edge of the film with a knife blade and pull. If this is a high-quality “American”, such a film is removed in a second, sometimes leaving an adhesive layer on the glass. If you are stopped on the road, then this may be enough to avoid paying a fine.
But the glue, anyway, will need to be cleaned later. If this is not done, when lowering the glass will cling to the seal, jam, making unpleasant sounds.
How to remove the glue from tinting
To remove the glue residue from the glass, it is necessary to wet the sponge and apply a small amount of baby shampoo or dishwashing liquid on it. Then wipe the glass well, wetting it abundantly with water and foam. And after that, walk around the glass with a scraper or blade.
Clean the remnants of the film or glue needed, keeping the blade at an acute angle to the glass. So it will not scratch it. If a remove tinted glass It does not work or the film is removed badly, it is torn on rags, help yourself with a hair dryer. Warm the film and scrape it off with a blade.
In this way, the glass is perfectly and quickly cleaned from the remnants of the film and glue. After that, you need to wash it again and wipe dry. Now you can use tools for washing windows.
Video, how to remove the tint and wash the glue from the side windows
How to remove the tinted rear window with heating
It is more difficult to remove the film from the rear window, which is heated. how remove tint without damaging the heated glass? To do this, you need the same tools that were described above, as well as a technical dryer. Keep in mind that if you have a high-quality film on the rear window, it will be much easier to remove it than to do it with Chinese products. And the guarantee that you do not damage the heating is also higher.
To remove tinted glass with a heated glass, heat it with a hairdryer, then pry the edge with a blade and slowly pull the film along the heating lines, continuing to use the hairdryer. But, with a high temperature, do not overdo it!
Usually, a good film is removed easily, leaving the heating safe and sound. Remnants of glue also need to be removed, but for this it is undesirable to use a blade or scraper, because it is very easy to damage the heating.
How to remove the adhesive from the film from the rear window
To remove the adhesive from tinting from the rear window, you can use a metal washcloth. The washcloth needs to be picked up as soft as you can find, and the metal chips in it should be the smallest.
If you do not find such a washcloth, you can usually use a sponge for washing dishes, which is soft on one side and hard on the other. Wet it up, add “Fairy” and start scrubbing the glue with a hard side. This should be done by moving parallel to the heating threads. After that, wipe the glass dry.
Video, how to remove the tint from the rear window with heating
Is it possible to restore the heated glass if it is damaged
What to do if you still damaged the heating threads? Is it possible to restore the heated glass? In some cases it is possible. On sale there are kits for recovery, for example, the American Permatex.
It includes an applicator, a brush and a bottle of solution. You can use a similar set, if the gap is small. But very few people satisfy the results of repairs using such tools. And not everyone can do it correctly and accurately. In this case, we can recommend only to change the glass by installing a new one with factory heating.
