For convenience, the owners often begin to redevelop their homes. Small windows do not provide enough light in the room, and therefore you have to replace them with more modern structures. House owners are faced with the question of how to make a door out of a window. In construction, this problem is solved in two ways. The first is quite simple and does not require much effort - when the wall under the window is demolished and a new structure is installed in its place. In the second case, it will take much more skill and effort: when to install the door you need to expand a very small opening. Then you need to change the jumper, which is responsible for durability and stability.

If the wall with windows is a carrier, then when installing the doors will require jumpers.

What you need to know before starting work?

It is worth considering separately the question of reinstalling the radiator, if it was located directly below the bottom of the window opening. Outside, you will need to install a window sill and fix the balustrade in the simplest version. If the event is more complex, you will have to cut through the wall. In the process you will need the following tools:

Corners of steel at an angle of 90 degrees, in order to make the jumper.
Channel bars
Reinforced concrete beams, when you cannot do without a new wall hole.
Perforator.
Ruler.
Bulgarian.
Sledgehammer for dismantling.
Mineral wool.
Polyurethane foam.

If the wall is load-bearing, then the overlapping structures should be fixed by using long vertical posts along the entire height of the dwelling. Most often the door is made exactly in the bearing partition that holds heavy plates. For such a case, it is necessary to use beams in order to sustain the future structure. If you live in an apartment building, then you should take care of the consent of the tenants and a special permit.

First, after you removed the window, you need to remove the lower partition. If it is made of brick, it breaks with a sledgehammer. If it contains metal elements, they are eliminated by the grinder. Products from gypsum cardboard understand in parts, at first screws get.

How to set the jumper, changing the parameters of the opening?

Often there are very small openings that subsequently expand. Sometimes in order to, you need to break a wall of several layers, for example, a brick one. Then the strengthening takes place in two stages: in the supporting structure and brick. It is rather difficult to do this work on your own, usually jumpers are bought. But you can do it yourself.

There are several types of jumpers:

Beams that withstand horizontal supports.
Constructions on which there are exclusively laying on top.
Interior lightweight beams.
Structures equipped with shelves for top loads, called bolts.

Depending on which room the future door will be in, it is worth starting. For cladding mount will occur through the corner. It must be greater than 80 mm. Fix it so that it is not visible in the laying of the opening of the former window. When dismantling, make sure that the parameters remain as smooth and symmetrical as they were. The angle should fit snugly according to 1/4 window dimensions in 50 mm.

There are 2 types of products, depending on their installation in the former window opening. Sometimes the jumper is poured immediately above it, and it happens that is attached later. The first type is more convenient in construction, it is also cheaper. This will allow no cost to enter the price of the door in the budget, because the design will not need to move a special crane.

Now make the formwork with the help of 20 mm thick wooden bars. Connect them through the use of screws. A row of planks is laid on the base horizontally in the dimensions of the cut window, and on top is the reinforcement. The second stage is knocking down a vertical row of boards with self-tapping screws.

The final components of the work

The armature must be tied with wire threads. In this case, the master can do without welding. And for the strength of the use of props, as they will have to withstand concrete.

It is important to provide in the space left by the facing masonry and lintel. Mineral wool 1 dm thick will serve you well. And on top of it will be a layer of concrete.

The window looked out on the street, so protection from the cold should be maximum and when re-planning.

Lay a brick on a layer of cotton wool and then spray the mounting foam so that the draft does not penetrate through the gaps in the door. Today there is an opportunity to take for insulation polystyrene foam 3 cm thick.

To prepare concrete for fixing the door, you need sand, cement, crushed stone. Pour concrete with reinforcement. To do this, lower it into the solution. After that, usually wait a day, then clean the formwork.

Remember that paint or excess plaster may remain in place of the window. Then it is time to insert the door frame instead of the window. Screw it in with screws or dowels. But before that, measure the level so that everything is smooth. Fill all extra space with foam for installation.

So, if you are tired of the existing plan of an apartment or house, then take up to change it. With certain skills in handling certain construction equipment, this can easily be done without help.

What must be present in the design of any home? Of course - these are doors and windows. Planning, selection and installation of door and window openings has many nuances. We will tell about some of them right now.

Standard sizes of windows and doors in a private house

The dimensions of these products largely determine the comfort of living tenants. Too narrow doors or small windows can cause many inconveniences. The size of the windows for a country house, as well as the parameters of the doorways, are regulated by building codes and state standards.

The adopted standards greatly facilitate the design of the building, allowing you to create optimal conditions for the use of residential premises.

Parameters for installing doors

The convenience of entering / leaving the premises directly depends on two interrelated parameters:

Standard doorway dimensions.
The parameters of the door leaf.

Standard domestic doors have a height of 1.9 or 2 meters and a width of 0.4 to 0.9 meters. Parameters of European models are slightly different. The height of such products is 202 and 215 cm, and the width can be 62, 72, 82 or 92 cm.

If you are planning to install conventional swing doors, the finishing opening for them should be 70-80 mm larger than the leaf itself. If your plans include installation of sliding doors, arrange an opening 50-60 mm less than the parameters of the canvas. It is worth noting that the openings of interior doors, as a rule, less than the parameters of the entrance.

Parameters for installing windows

Accepted standards for the installation of windows in a private house, as well as for balcony doors, are determined by the state standard 11214-86. According to regulations, the width of a standard opening varies from 870 to 2670 mm, and its height ranges from 1160 to 2060 mm. Doors to the balcony have a single height (2755mm), but may vary in width: 870, 1170 or 1778 mm.

Parameters depend on several factors:

The area of the room.
Necessary lighting.
Architectural specificity of the room and the building itself.

Depending on what window opening is planned in the house, the glazing system is determined, as well as the required number of casements and transoms.

In addition, GOST regulates the height of window sills, which must be considered when organizing openings.

The window sill in the bedroom should be at a height of 700-900 mm, in the kitchen - 1200-1300mm. Also, their standards have window sills for bathrooms and utility rooms. For the first, the height of the sill should not be less than 1600 mm. For the latter, this value should be in the range from 1200 to 1600 mm.

Custom size of the window opening in the house

Modern technologies and the preferences of the owners allow you to create projects of houses that use non-standard windows. The windows in the cottage, the dimensions of which depend on the characteristics of the building, can be triangular, trapezoidal, semicircular, circular or arched. Such products give the house a personality, but their layout and installation has its own nuances.

Door and window openings for houses from different materials

The layout for a private house depends largely on what materials it was built from.

Door and window in a wooden house

The organization of windows and doors in wooden buildings requires the preparation of a special structure (frame). Its task is to compensate for the shrinkage of the log house, characteristic of wooden buildings.

To install the openings in the log cottage you will need:

Installation of a bar with a gasket for insulation on a pre-prepared slot.
Installation of casing.
Processing gaps heat-insulating materials.
Installing the door leaf or window unit in the casing.
Decorative design: installation of ebbs and slopes.

When installing the casing, it is very important to leave a gap on top in case of shrinkage of the structure.

The size of the gap depends largely on the degree of moisture of the wood used, while not exceeding 6-7% of the entire height of the opening. A properly mounted casing protects windows and doors from being “squeezed out” as the building shrinks.

Door frame and window opening in a log house

The organization of windows and doors in timber structures is practically the same as the installation of window openings in a log cottage.

As in the first case, the installation of products required to organize the casing construction.

The casing is mounted without capital attachment. To install it, the system is “tongue and groove”. Thanks to this design, windows and doors are not deformed when the house shrinks from a bar.

During installation, it is necessary to ensure that the mounting foam does not connect the casing with the wall. Otherwise, the casing construction will not be able to fall along with the shrinkage of the house.

Doors and window opening in a brick house

Work in brick houses requires the installation of special ceilings. As them, you can use steel profiles, iron bars or reinforced concrete lintels.

The window in the brick house is set at a height of 10 rows of brickwork. The doorway should be mounted after 2 rows of brick masonry. These parameters are recommended by the standards adopted in construction. However, they can be adjusted depending on the height of the erected structure.

Installation features for frame type structures

If you are going to install a window opening in a frame house, you must take into account the characteristics of the material of buildings of this type.

Build on Canadian technology? This means that you need to use dual racks. This solution will allow you to correctly distribute the weight of the structure itself and the weight of the window without affecting the entire structure.

In Finnish frame houses are installed single stand for windows. A special element of the frame house - the bolt will allow you to optimally distribute the weight of the structure.

Other nuances of the selection of window and door openings

As we said earlier, the organization of openings for doors and windows requires adherence to a number of nuances.

Installation of the balcony unit also has its own characteristics. The top line of the balcony door should be in line with the top side of the window. And the exterior finish of the floor should exceed the bottom line of the balcony opening by 10 cm.

We hope that this information was useful to you. Remember that for the implementation of any construction projects it is better to contact people who have professional experience in such matters.

We wish you success in all your endeavors!
Zabaluev S.A.

Decision No. 2-1600 / 2015 2-1600 / 2015 (2-6974 / 2014;) ~ M-4770/2014 2-6974 / 2014 M-4770/2014 of April 9, 2015 on case No. 2-1600 / 2015

Case number 2- 1600/15

DECISION

In the name of the Russian Federation

Oktyabrsky District Court. Izhevsk composed of:

Presiding judge Ivanova MA,

When Secretary Vshivkovoj AND.A.,

Having considered in open court a civil case under the claim of Kataev P.M. to Ivantaeva F.Z., Buzanov V.N. about the compulsion to eliminate the unauthorized reorganization of the premises,

y with t and N about in and l:

Kataev P.M. Originally filed a lawsuit with Ivantaeva FZ on elimination of violations of the rights of the owner of the dwelling, the obligation to bring the room to its original state

The claims are motivated by the fact that the claimant is the owner. In July 2014, a doorway appeared from the outer wall of the front facade of the house, instead of a window in a non-residential room (rooms on floor plan 36-42, floor: basement) belonging to the respondent, a separate entrance to the land plot, which is in common ownership all tenants, including the plaintiff. Meanwhile, the defendant does not have both permits and the consent of all owners of residential premises to use the common property of an apartment building.

Based on the above, the plaintiff requested to oblige the respondent within one month from the date the decision enters into legal force to bring non-residential premises, basement floor, numbers on the floor plan 36-42, at:, in its original condition in accordance with the technical passport to the house, dismantling the doorway with the door, restoring the brickwork and facing the outer wall of the front facade of the house in the place of the doorway, restoring the window opening.

He also requested to recover legal costs of paying the state fee, representative services in the amount of 20,000 rubles.

By a court ruling, at the request of the plaintiff, Buzanov V.N., who is 1/2 the share of the disputed non-residential premises, was involved as a co-respondent in the case.

The plaintiff Kataev P.M., being duly notified of the date and place of consideration of the case, did not appear at the court, submitted a statement of consideration of the case in his absence. In previous court sessions, he insisted on the claims, clarified that his rights were violated by a decrease in the common share ownership, while his opinion was not clarified, his consent was missing. The plaintiff dismantled the outer part of the wall by expanding the window opening for door installation, occupied a part of the land plot adjacent to the house, which is a change in the parameters of the capital construction object, as the property of the owners of the apartment building’s building diminished. related to enclosing structures.

i decided:

The claim Kataev P.M. to Ivantaeva F.Z., Buzanov V.N. about the compulsion to eliminate the unauthorized reorganization of the room to satisfy.

To oblige Ivantaeva F.Z., Buzanova V.N. within one month from the date the decision enters into legal force, bring non-residential premises, basement floor, numbers on floor plan 36-42, at:, in its original condition in accordance with the technical passport to the house, by dismantling the doorway with the door, restoration of brick masonry and cladding the outer wall of the front facade of the house in the place of the doorway, the restoration of the window opening.

To recover from Ivantaeva F.Z., Buzanova V.N. in equal parts in favor of Kataev PM court costs in the amount of 10 200 rubles. 00 cop., At 5100 rubles. 00 cop from everyone.

The decision may be appealed to the Supreme Court of the Udmurt Republic within a month from the date of its adoption in final form through the district court.

Presiding judge MA Ivanova

To equip a doorway in the bearing wall is not an easy task if you decide to work from scratch. It is not always possible to break through a new passage, because the construction of the house as a whole may suffer from this. Let's look at what needs to be considered in this case and how to cope with this task in certain conditions.

The doorway in the supporting wall requires mandatory reinforcement

Important aspects

Quite a lot of people are worried about the question whether it is possible to make a doorway in the supporting wall of a brick or panel house. In general, such a decision is allowed subject to the necessary conditions, but any redevelopment of such a plan is undesirable. Bearing walls are subjected to enormous loads, and therefore violation of the technology of work performance can lead to the destruction of floors and the house as a whole.

The transfer of the doorway must be coordinated with the special service. It may take several months to bring this process to the end; therefore, such options should be thought out in advance.

In order to avoid mistakes, the following important aspects should be considered:

the material that was used in the construction of the house;
dwelling layout;
the ratio of the size of the opening and the bearing wall;
condition of the house and, in particular, floors;
the load that is on the wall from above;
thickness and condition of the wall.

The thickness and condition of the wall is one of the important aspects in organizing the opening in the supporting wall

Project opening

If you have conceived the transfer of the doorway in the construction of the supporting wall, first of all, you need to decide on the project. This will directly affect the order of work and their complexity.

The following options are possible:

Simple doorway in the plane of the bearing wall. This is an opening of standard dimensions, which runs from scratch in a new place. However, the existing passage can be closed or remain intact, which will also affect the load distribution.
Arched doorway. A more complex option, since it is necessary to take into account the shape of the bends. For brick walls, only a professional can perform such work, as a relationship with the location of the seams of the brickwork is required.
Minor carry over. This is the easiest and most secure option. In this case, the lintel is shifted to the side, part of the existing passage is stitched or laid with brick, and a fragment of the wall of the required size is cut from the side.

Varieties of doorways in the bearing wall

Used tools and materials

For punching the opening in the bearing wall requires a special tool. It is not recommended to use a perforator, as rough intervention and vibration can lead to the formation of cracks and chips.

For cutting walls are used:

Cable cutting. Special installation, based on rope cutting elements with artificial diamonds on the sleeves.
Diamond drilling. For work use strong drills with a diamond dusting of a cone-shaped form or with square section.
Diamond cutting saw. In this case, it is recommended to use a diamond-coated disk nozzle for wet cutting and a tank with water. This will cool the tool and prevent excessive dust formation.

Tools used for cutting walls

Carrying a doorway is a painstaking process. Be prepared for the fact that there is a lot of dust and debris in the room. It is recommended to completely remove the furniture and appliances at the time of repair.

Panel house

The actual question for apartment owners is how to make an opening in the supporting wall of a standard panel house? In this case, it is intended to cut out a part of the concrete slab that holds the upper tiers. In order to redirect the load from this area, steel lintels should be used.

First you need to mark the wall according to the developed project. Then holes are drilled along these marks, meaning base points. The main ones are upper corner ones, focusing on them you can remove a part of the concrete and lay a jumper. If you are doing it in two parts, for the beginning, you should install each half in the opening, calling at a certain distance beyond its borders. Then drill the holes for the screed with bolts, tighten them as tightly as possible and block.

As long as the solution does not dry out, it is impossible to continue the work; this may compromise the integrity of the structure.

After the concrete hardens, you can proceed directly to cutting out the opening itself. For these purposes, use diamond cutters. Work needs to be phased:

To begin, cut the overall contour to a small depth on both sides, focusing on the drilled marks.
Then divide the entire inside area into small sections.
Saw the wall into these pieces and alternately knock out of the opening.

The lintel is a key element in creating a doorway in a panel house.

If you decide to create an arched vault, you need to use a bent channel to strengthen the opening. Additionally install strapping on the sides. In this case, all elements of the supports must follow the contours of the future opening.

Brick house

In order to equip the opening in the supporting wall of an apartment brick house, it is necessary to slightly change the method of work. The first stage as a whole remains unchanged. It is necessary to outline the approximate location of the opening and its shape. Then remove the top layer of plaster in order to release the brickwork. So, you will see all the seams and details of the wall, which will allow you to easily adjust the project to specific conditions.

All contours and details need to be corrected taking into account the location of the brick joint. In order for the jumper to perform its functions, it is fully necessary to place it directly in the inter-seam space. A drill is also used to transfer the contours and a through hole is made.

Since it is somewhat more difficult to make an opening in the bearing brick wall, it is necessary to take care of the presence of auxiliary supports and jumpers in advance. Until you fix the channels, you need to provide support for the upper stonework. care must be taken, it is best to use diamond drills to minimize damage.

An important step in creating the opening in the bearing brick wall is to secure the channel

In order to strengthen the opening for a brick house, it is recommended to additionally use a metal structure made of corner profiles and plates, installed directly around the perimeter of the passage made. All parts are bolted together as well as by welding. After that, you can begin to finish and install the box.

Before you begin to redevelop such scales, be sure to consult with experts and get the appropriate permission. You can miss important details that will further affect the sustainability of the house as a whole. You should not risk security for the sake of bold design ideas.

Telephone consultation 8 800 505-91-11

The call is free

Door instead of window

House in common share ownership. One owner wants to make a door in his wall instead of a window - access to the street, so as not to walk around the common courtyard. How to arrange it, whether the consent of other owners?

Hello dear visitor of the site, without your consent, he can not do it, and your walls may collapse, as the window in the main wall is located. Good luck to you and all the best, respectful lawyer Ligostaeva A.V.

I bought an apartment in a brick house on the 6th floor, they made a door instead of a window for access to the loggia, this was not legalized. What should new owners do?

If the reconstruction does not affect the bearing wall, then it can only be legalized in a court of law, since the works have already been completed. If the bearing wall is offended, the court will refuse and will oblige to bring it to its original state. You can go to the designers, if you find it difficult to determine whether the bearing wall is affected or not. The court will still need their technical opinion.

Bought an apartment. It 1) removed 3 built-in wardrobes, 2) a door and a metal staircase were made instead of a window. When inspecting and discussing transactions with realtors, we were verbally confirmed that everything was legalized.
As they made out the mortgage and ordered the report to the appraiser, there was no doubt about the authenticity of the documents. After the transaction, I requested a report from the appraiser - he did not notice (!) The absence of built-in wardrobes and the presence of an iron door with an iron staircase instead of a window. What are the consequences, the risks I bear as a new owner, and how to reduce them to the minimum?

Hello. You can legitimize yourself. After building technical expertise.

Can I make a door instead of a window in a multi-storey house built of panels?

Maybe, but for this you need 100% for the general meeting of all owners of the house, since the wall is a common property of the MKD.

Neighbors on the 1st floor removed the window and instead put the door, cutting through the window opening, thereby not informing anyone and not presenting any papers for permission. What are our actions ?! Who to contact? We have the HOA.

Contact the housing inspection, the prosecutor's office to conduct an inspection. In court on bringing the premises to the original position. Must be architecture resolution.

A shower is installed in the bathroom instead of a bath, and an arch is made in the kitchen instead of the door to the balcony and the windows, is this an illegal redevelopment? After the arch was made, the loggia was insulated, glazed, and a battery was hung there. The apartment has independent heating. Appealed on this issue to the BTI, they replied that it is not considered a redevelopment. I also wanted to hear your answer. Do I need to make these changes in the apartment in the cadastral passport?

If you have already been answered by BTI specialists, then we are all the more not experts in this field. And how will you make a change in the cadastral passport without the conclusion of BTI specialists,

Good day! Replacing plumbing fixtures, sinks, plates and pipes with similar ones in parameters and purpose, but provided that their location does not change is not a re-planning! You all correctly answered.

If during the creation of the arch the outer wall was broken - then this is a redevelopment, you can be instructed - by the administration - that you would bring the wall into its original form.

Good day to you. If BTI specialists have already answered you, then we will not be able to answer you anyway. I wish you good luck in solving your question.

According to Art. 25 LCD RF redevelopment of residential premises is a change in its configuration, and the reorganization of residential premises - installation, replacement or transfer of engineering networks, sanitary, electrical or other equipment, requiring changes in the technical passport of residential premises. The order of actions of interested persons, as well as the grounds for the reorganization and (or) redevelopment of residential premises are established by Art. 26 LCD RF. Works that may include these concepts are listed in clause 1.7.1 of the Rules and Regulations for the Technical Operation of the Housing Fund, approved by Decree No. 170 of the Gosstroy of the Russian Federation of September 27, 2003. In particular, redevelopment of residential premises may include: transfer and disassembly of partitions, transfer and installation of doorways, dividing or enlarging multi-room apartments, arranging additional kitchens and bathrooms, expanding living space through auxiliary premises, eliminating dark kitchens and kitchen entrances through apartments or veins premises, equipment or renovation of the existing platform. "In the kitchen instead of the door to the balcony and the windows an arch is made" - here you have removed part of the wall under this window - this is an extension of the area due to the auxiliary premises. I think you should still get a new technical plan and legitimize your work. There are questions - you can call.

Is it possible to install a door to the loggia instead of the window (disassemble the brickwork under the plastic window and put the door and window to the floor)? the loggia will not be heated. The house is brick, apartment on the 6th floor. If you do, and then legitimize in BTI, is there a large fine?
Is it possible to remove the non-carrier partition between the kitchen and the room so that there is a large kitchen-living room? The remaining 2 rooms are fenced off with doors. The apartment is a new open plan house brick, gas stove.

Good day. To make such a reconstruction you need to get permission from the administration, for this you first need to prepare a project. Legalize the BTI will not succeed, BTI just make peremery and reflect the presence of illegal reconstruction in the data sheet on the apartment. Then you have to contact the Administration with a statement to legitimize. In practice, the Administration usually refuses, after which you will need to go to court with a claim. Therefore, it is better to do everything legally - and the nerves are smaller and cheaper. Just prepare the project and get permission for this project in the Administration.

Question about the device of a separate entrance to a residential apartment on the 1st floor, by installing a door instead of a loggia window (not a bearing wall).
Namely, the consent of the owners of the house. How many consents to collect? The house is 2 years old (450 apartments) and it is occupied by no more than half.
Information from the Criminal Code - you need 50% +1 vote (hard to reach), from the town planning committee - 100% (which is not even theoretically possible).

Since we are talking about making constructive changes in common property, which are the walls of the house, it is necessary to obtain the consent of all owners. If not all apartments are sold, the missing part can be agreed with the developer.

Unfortunately - most likely it will not work with a separate entrance, you have reduced the total property, which means that Pgo Art. 36 LCD RF - you need the consent of all homeowners in the house.

Good day. Since it is a question of changing the construction of the common property of all owners in accordance with Article 36 of the Housing Code, the Consent of all owners of residential premises must be obtained.

Good day. Alas, it was rightly said that the consent of all the owners of the house is required, article 36 of the housing code. All the best and thanks for contacting the site.

Good afternoon! I have a non-residential premises on the 1st floor, instead of the window you need to mount the front door. Do I need the consent of the neighbors?

Good day. First of all you need the consent of the administration for the reconstruction. To do this, you need to prepare a project and apply with the appropriate application to the administration.

We rented non-residential premises in a brick house, we want to make a door instead of a window, without a porch. Just a metal door. In fact, we do not do the reconstruction of the facade of the building, we just do the redevelopment, we remove the window sill. The width of the door will be the same width as the window, do we need the consent of 2/3 of the owners for this redevelopment?

You need 100% consent of the owners of residential and non-residential premises in the house, as the outer wall of the house decreases, which is common property, the disposal of which requires the unanimous decision of all owners.

Can I install a door instead of a window in the living room?

It depends on what you mean. LCD RF. Article 26. The basis for the reorganization and (or) redevelopment of residential premises 1. The reconstruction and (or) redevelopment of residential premises shall be carried out in compliance with the requirements of the legislation by agreementwith the local government (hereinafter - the body that carries out the coordination) on the basis of its decision.

Is it possible instead of a balcony to make a railing from the floor, and to alter the windows in the door?

Only with the permission of the administration. Apply to the municipality. And get approval for the collection of the MKD, article 44,46 LCD RF.

Is it possible to cut through the door, instead of a window in a residential building, thereby making a separate entrance on the first floor, without a porch. The apartment is located in the city of Penza. What authorities do you need to contact if it is legal?

Hello, Article 7.21. Violation of the rules for the use of residential premises 1. Damage to residential buildings, residential premises, as well as damage to their equipment, unauthorized reorganization and (or) redevelopment of residential buildings and (or) residential premises or their misuse - entails a warning or imposition of an administrative fine on citizens in the amount of from one thousand to one thousand five hundred rubles. 2. Unauthorized re-planning of residential premises in apartment buildings - shall entail the imposition of an administrative fine on citizens in the amount of from two thousand to two thousand five hundred rubles. See the text of the article in the previous edition Good luck to you and all the best.

An expert builder can answer this question (about the technical possibility of such a reconstruction of your house). Contact an expert organization that has such a specialist on staff.

Hello. With this question you need to contact your local architecture. They get permission. It will be necessary to conclude that the state of the main building structures will not be disturbed. All the best. Thank you for choosing our site.

Hello. To do this, you need to order a reconstruction plan and obtain a building permit from the city administration (in the Architecture Department). But for residential premises such permission is usually not issued. Now, if the apartment is transferred to the non-residential category and will be used as an office, then most likely, such permission will be issued. God help you.

Instead of a window in a non-residential premise, put a door - is it necessary or not to agree the occupants of the whole house?

You do not pretend to use common areas, therefore you don’t need the consent of the owners, but the consent to the redevelopment of the premises from the municipality is required.

I live on the 1st floor, 17 years ago I made a glass door instead of a window, now 17 years later they demand that the door be removed and the window be installed! The apartment is private! Are you entitled to this?

Hello. Yes, if the door is installed without permits

She and her husband lived in his apartment without registration. The repair was done. Door windows were made together and everything was registered in my name. I have documents and furniture. I can go into the apartment and take anything out of furniture without a trial.

If the husband is not against it. You lived without registration. Share the property.

The point is in personal relations, if you are already divorced, the husband’s apartment, he may not let you in, since this is private property, only the division of property remains. Try to negotiate a division before trial by an agreement.

Question: in 1 square. Square. on the 1st floor (corner) make the door instead of the window. Consent of the tenants, transfer to non-residential fund is necessary? Or not. Project, coordination with local organizations. G. Gremyachinsk Perm Region. Under the store selling app. parts. Oils and chemicals are excluded, only iron. Thank.

Hello! Consent must tenants GOOD LUCK YOU

Tell me please, if instead of the window (exit from the room to the street) put the door. Is this considered redevelopment? It’s just that the old man has no other entrance; he is climbing through the window to his home on a stepladder. The apartment is for several owners, they put a wall to him and now he is without entry and exit.

yes, this is a redevelopment, you need the consent of the MO administration

The complaint against the owners must be filed with the court.

In 1 to the apartment window was demolished in the kitchen and the door to the loggia was inserted instead. And from the kitchen to the loggia transferred batteries. Is it possible and how difficult is it to legalize such redevelopment?

you need to take a conclusion in the SES, BTI, draw up a draft redevelopment and go to court.

Can I make an additional door instead of a window in the house where there are 4 apartments (it is considered multi-room, apartments have rooms), but I want to make an additional balcony.

Hello! You can, only with the permission of all co-owners.

Can I remove the window in the kitchen overlooking the loggia and put the door instead of the window?

you can, in this case does not affect the supporting structures and the intended use of the premises

Is it possible to tear the cabinet under the window, and instead of the window to put the door?

Can. If you get permission.

In the new building, access to the balcony would be desirable to remove the window and the door to the balcony, only instead of them (windows and doors) to put sliding doors glass-plastic. Do you need permission for this and where to get it?

To redevelop the living space you will have to take permission from Art. 29 LCD RF)

In general, this redevelopment, permission to moszhilinspektsii.

How to rent an apartment to the enterprise on the first floor, make the door to the street instead of a window, legally?

To do this, you need to move the apartment into a non-residential space.

Hello. First, you get permission for re-equipment in the management of housing and communal services or construction. Then make a lease or rental agreement with the company. If the living room, then hiring.

I live with a grandson on the 1st floor of a corner apartment. How to make a separate exit to the street instead of a window-door; where to start where to turn.?

This is a redevelopment of the apartment (as well as reconstruction, depending on the project). Making redevelopment is quite expensive and time consuming. You need to start with an appeal to the Committee of construction control of the city administration for permission to agree on the redevelopment. The following documents will be needed: Application for redevelopment according to the form, documents of title to the apartment, project of redevelopment, technical passport of the apartment, written consent of all members of the employer's family, conclusion of the body for the protection of architectural monuments.

If instead of the window between the kitchen and the balcony do the door is a reconstruction?

Yes, this is a reconstruction.

Is it considered redevelopment if we want to remove the balcony door with the window? That is, we will not touch the stone partition, which is under the window! Just make an exit to the loggia open. Do you need permission to do this?

With this question you need to contact Moszhilinspektsiyu.